
Ballistic Calculator
Free ballistic calculator.
Enter your bullet, BC and muzzle velocity and get drop in inches, the dial-up in MOA and MIL, wind drift, velocity, energy and time of flight at every range. Free, no signup.
Then change anything below to match your rifle. Your chronographed velocity beats the box.
Air, wind angle and table range
Swipe the table for MIL, wind, velocity and energy →
| Range (yds) | Drop (in) | Elev (MOA) | Elev (MIL) | Wind (in) | Velocity (fps) | Energy (ft·lb) | Time (s) |
|---|---|---|---|---|---|---|---|
| 100 | 0.0 | 0.0 | 0.0 | 0.8 | 2456 | 2250 | 0.12 |
| 200 | -4.3 | 2.0 | 0.6 | 3.2 | 2271 | 1924 | 0.24 |
| 300 | -15.3 | 4.9 | 1.4 | 7.5 | 2094 | 1636 | 0.38 |
| 400 | -34.3 | 8.2 | 2.4 | 13.9 | 1925 | 1382 | 0.53 |
| 500 | -62.6 | 12.0 | 3.5 | 22.6 | 1765 | 1162 | 0.69 |
| 600 | -102.2 | 16.3 | 4.7 | 33.9 | 1615 | 973 | 0.87 |
| 700 | -155.1 | 21.2 | 6.2 | 48.2 | 1477 | 814 | 1.07 |
| 800 | -224.0 | 26.7 | 7.8 | 65.7 | 1352 | 682 | 1.28 |
| 900 | -311.9 | 33.1 | 9.6 | 86.5 | 1243 | 576 | 1.51 |
| 1000 | -422.5 | 40.3 | 11.7 | 110.8 | 1152 | 495 | 1.76 |
Point-mass solver with the standard G1 drag table and air-density corrections. Wind assumes the speed above at the angle set (90° is a full-value crosswind). Spin drift and Coriolis aren't modeled; they matter past about 1,000 yards. Confirm everything on the range.
What a ballistic calculator does
A ballistic calculator predicts where your bullet will be at any distance. It starts from how fast the bullet leaves the barrel and how well it cuts through air (its ballistic coefficient), then steps the bullet downrange, slowing it with drag and pulling it down with gravity, to tell you how far below your aim it lands and how much to dial.
The inputs that matter most
- Muzzle velocity. The biggest lever by far. Factory numbers come from long test barrels; chronograph your own rifle.
- Ballistic coefficient (G1). From the box or the bullet maker. Higher BC means a flatter trajectory and less wind drift.
- Zero distance and scope height. These set where the bullet crosses your line of sight. Most precision shooters zero at 100 yards.
- Air. Temperature and altitude change air density, which changes drag. The defaults are standard sea-level air (59°F).
Reading the table
Drop is inches relative to your point of aim (negative is low). Elev is how far to dial up in MOA or MIL to hit at that range. Wind is drift for the wind you entered, which by default is a 10 mph full-value crosswind. Velocity and energy tell you how much bullet is left, which matters for hunting and for staying supersonic.
Want a quick reference instead? The drop charts have ready-made tables for popular factory loads, and the dope card builder prints your numbers on a card for the rifle. For bullet energy alone, use the bullet energy calculator.
Ballistic calculator: common questions
How accurate is this ballistic calculator?
It's a point-mass solver using the standard G1 drag table, the same family of model most free calculators use. Checked against Federal's own published tables for Gold Medal Match .308, .300 Win Mag and .338 Lapua, it matches velocity and wind drift to within about 1% out to 500 yards. Your inputs matter more than the model: a muzzle velocity that's 50 fps off moves your 1,000-yard drop by more than a minute of angle.
What's the difference between G1 and G7 BC?
They're BCs measured against two different reference bullets. G1 is the flat-base reference most manufacturers publish; G7 matches modern long boat-tail bullets more closely over a wide speed range. This calculator uses G1, so enter the G1 number from the box or the bullet maker's website. A G7 value plugged in as G1 will badly overstate drop.
Why does the bullet print low at 25 and 50 yards?
Your scope sits above the bore, so the bullet starts below your line of sight and climbs to meet it. With a 100-yard zero, it's still below the line of sight at 25 and 50 yards by close to the scope height, then rises, crosses at the zero and falls away after.
Does altitude change bullet drop?
Yes. Thinner air at altitude means less drag, so bullets keep more velocity and drop less. A load that drops 400 inches at 1,000 yards at sea level can drop noticeably less at 6,000 feet. Temperature works the same way: hot air is thinner, cold air is denser.
What scope height should I use?
Measure from the center of the bore to the center of the scope tube. A typical bolt gun with standard rings is around 1.5 inches; an AR-15 with a cantilever mount is usually 2.5 to 2.8 inches. It mostly affects your close-range numbers.
How do I use the MOA and MIL columns?
Those are how far to dial your scope up to hit at that range. Use the column that matches your turrets: MOA scopes usually click in quarter-MOA, MIL scopes in tenths of a MIL. To convert or count clicks, use the MOA and MIL calculator.
Drop charts by caliber
Be first
Get the Chambered app the day it launches.
Your rifles, loads and dope cards in one place, plus state-law-change alerts. No marketing fluff. Unsubscribe with one click.